• Tablet Feeder, Liquid Feeder
• Sizes: 1.5", 2.5", 4", or 4.5" NST connections
• Uses: Hydrant Diffuser, Hydrant Flusher, Dechlorinator

Bazooka tablet or liquid feeder for hydrant and water main flushing/dechlorination. Comes in two varieties, one for tablet and one for liquid injection. 1.5", 2.5", 4" and 4.5" NST connections available. Dechlorination during flushing programs is critical for the health of our waterways as the chlorine will prove to be toxic to fish and other life. Using a dechlorinator is a simple means to ensure chlorine is completely and safely removed

Tablet Feed: How It Works

By opening the hydrant valve, a small amount of water is bypassed from the pressure side of the Bazooka venturi to the rate valve flow meter assembly and supplied to the bottom of the tablet chamber dissolving the tablets in a precise manner. The dechlorination solution is then pulled into the system, making a homogeneous mixture proportioned and controlled to ensure that all water is in contact with the correct amount of chemical. Adjusting the flow meter setting provides precision chemical control to avoid chemical waste or over dechlorination.

Liquid Feed: How It Works

From the open hydrant valve, water passes through the unit creating a vacuum which pulls the dechlorination chemical from its supply container into the system via the rotometer rate valve assembly. The rotometer rate assembly provides precise control of the dechlorination solution strength to avoid chemical waste or over dechlorination.

• Tablet Feeder
• Material: Steel or Aluminum
• Uses: Hydrant Diffuser, Hydrant Flusher, Dechlorinator

• Tablet Mat
• Sizes: 3 pocket, 6 pocket, 24 pocket
• Uses: Hydrant Diffuser, Hydrant Flusher, Dechlorinator

• Tablet Sock
• Sizes: 1 sock (holds approximately 10 tablets)
• Uses: Hydrant Diffuser, Hydrant Flusher, Dechlorinator

• For chlorination or dechlorination tablets
• LF Series Inlet /Outlet size range: 4” up to 8”
• LF Series Minimum Flow: 75 GPD (LF1000)
• LF Series Maximum Flow: 400,000 GPD (LF4800)
• Constructed of durable PVC
• Installed at or below grade
• LF Series Minimum Number of Tubes: 1 (LF1000)
• LF Series Maximum Number of Tubes: 4 (LF4600 & LF4800)

• For chlorination or dechlorination tablets
• 2000 Series Inlet /Outlet size: 4”
• 2000 Series Minimum Flow: 200 GPD
• 2000 Series Maximum Flow: 100,000 GPD
• Constructed of durable PVC
• Installed at or below grade
• 2000 Series Number of Tubes: 2

• For chlorination or dechlorination tablets
• 4000 Series Inlet /Outlet size: 6”
• 4000 Series Minimum Flow: 20,000 GPD
• 4000 Series Maximum Flow: 200,000 GPD
• Constructed of durable PVC
• Installed at or below grade
• 4000 Series Number of Tubes: 4

Specifications

• Size: 3/4 to 25 gallon
• Maximum Pressure: 125 or 300 PSI valving
• Includes: Larger units with legs

The SF feeders are constructed from steel pipe with machine welded steel ends. The threaded connections are heavy steel half-couplings machine welded to the end plates of the feeder. SF feeders are furnished with brass valves and schedule 40 steel nipples. Feeders with the HP option have 600 PSI steel ball valves and schedule 80 steel nipples.

5 gallon and larger feeders have three 12" legs.

125 psi shot feeders include (1) feeder body, (2) 1" gate valves, (2) 1/2" gate valves, (3) 1" nipples, (2) 1/2" nipples, (1) poly funnel

300 psi shot feeder includes (1) feeder body, (2) 1" ball valves, (2) 1/2" ball valves, (3) 1" nipples, (2) 1/2" nipples, (1) poly funnel

Specifications

• Size: 3/4 to 25 gallon
• Maximum Pressure: 125 PSI valving
• Includes: Larger units with legs

The BPF feeders are constructed from steel pipe with machine welded steel ends. The threaded connections are heavy steel half-couplings machine welded to the end plates of the feeder. BPF feeders are furnished with brass valves and schedule 40 steel nipples. The feeders are only available with 125 PSI brass valves.

5 gallon and larger feeders have three 12" legs.

125 psi by-pass feeders include (1) feeder body, (1) 1" gate valve, (3) 1/2" gate valves, (2) 1" nipples, (2) 1/2" nipples, (3) 3/8" nipples, (1) 1" x 3/8" bushing, (1) 1/2" x 3/8" bushing, (1) 3/8" union, (1) 3/8" needle valve, (1) gauge glass assembly, (1) poly funnel

Specifications

• Size: 50 or 100 gallon
• Material: Polyethylene, carbon steel or overpack
• Electrical: 120 VAC, 60 Hz, 20 amp
• Item Weight: 861 lbs

Closed system leaks due to faulty valves or plumbing leaks can significantly reduce the glycol concentration of the system. The AF Closed Loop Glycol Feeders maintain a consistent operating pressure and a controlled level of glycol in a closed loop system.

The Glycol Feeder is a completely packaged unit consisting of a tank, pump, and a control panel all pre-wired and assembled requiring only a 120 VAC electrical supply power connection and a discharge piping connection to the closed loop.

The NEMA 12 control panel allows for manual ON-OFF pump control or automatic pump control by the closed loop system pressure. An audible and visual alarm warns operators of low liquid level in the supply tank and shuts off the pump. The terminal strip in the panel has terminals for wiring in a remote alarm. Wiring between the control panel and the pump, pressure switch, and low level switch is in liquid tight conduit.

The glycol pump is a 1/2 HP bronze gear pump which supplies positive glycol feed to the closed loop. A pressure relief valve is installed in the discharge piping on the unit to protect against over pressure and an inline check valve prevents system fluid from contaminating the glycol in the supply tank. A pressure switch in the discharge piping senses the closed loop system pressure and controls the pump operation when the control panel switch is in the AUTO position.

The Glycol Feeder can be modified to suit individual applications. For example, a Glycol Feeder can be fitted with two pumps and discharge assemblies to accommodate two closed loop systems.

• Tablet feeder mounting bracket
• Used with Norweco 2000 Series Tablet Feeders
• Corrosion resistant aluminum assembly
• Size: 18 1/2" H, 26 1/4" L, 11 3/4" W
• Mount in a contact tank or other enclosure

• 2000 Series Locking Assembly
• Used w/2000 Series Tablet Feeders
• Prevents unauthorized access
• Must be installed at the factory
• Includes: padlock, cable ties and angle brackets

• 2000 Series Tablet Feeder Riser Assembly
• Used w/2000 Series Tablet Feeders
• Can use one or more 24” riser
• For use in direct burial installations
• Includes trim lines at 6” vertical increments, 2 remote feed tube removal systems, 14 drive rivets and 3 oz. tube sealant.

The tablet feeder remote removal system is for below-grade replacement of feed tubes and includes a set of two 12" extensions, 12" handles and 2 caps with top threads to replace the standard caps.

• 2000 Series Sluice Adjustment Set
• Used w/2000 Series Tablet Feeders
• 5/8” corrosion resistant steel socket assembly
• Used to adjust outlet sluice when risers are used

• Tablet feeder mounting bracket
• Used with Norweco 4000 Series Tablet Feeders
• Corrosion resistant aluminum assembly
• Size: 23" H, 36 3/4" L, 16" W
• Mount in a contact tank or other enclosure

• 4000 Series Locking Assembly
• Used w/4000 Series Tablet Feeders
• Prevents unauthorized access
• Must be installed at the factory
• Includes: padlock, cable ties and angle brackets

• 4000 Series Tablet Feeder Riser Assembly
• Used w/4000 Series Tablet Feeders
• Can use one or more 24” riser
• For use in direct burial installations
• Includes trim lines at 6” vertical increments, 4 remote feed tube removal systems, 18 drive rivets and 3 oz. tube sealant.

The tablet feeder remote removal system is for below-grade replacement of feed tubes and includes a set of four 12" extensions, 12" handles and 4 caps with top threads to replace the standard caps.

• 4000 Series Sluice Adjustment Set
• Used w/4000 Series Tablet Feeders
• 1” corrosion resistant steel socket assembly

Hitch Mount for #ER-250 Hydrant Flusher

Low Flow Fins for #ER-250 Hydrant Flusher

Pitot Gauge for #ER-250 Hydrant Flusher

Screen for #ER-250 Hydrant Flusher when using Ascorbic Acid tablets #1230ASCACI.

Tire Mount for the #ER-250 hydrant flusher tablet feeder.

• Tablet feeder mounting bracket
• Used with Norweco 1000 Series Tablet Feeders
• Corrosion resistant aluminum assembly
• Size: 9" H, 10 3/16" L, 8 1/2" W
• Mount in a contact tank or other enclosure

• Tablet feeder mounting bracket
• Used with Norweco LF2000 Series Tablet Feeders
• Corrosion resistant aluminum assembly
• Mount in a contact tank or other enclosure

• Tablet feeder mounting bracket
• Used with Norweco LF4000 Series Tablet Feeders
• Corrosion resistant aluminum assembly
• Mount in a contact tank or other enclosure

Specifications

• Material: Poly
• For Use With: BPF Bypass Feeder
• Item Weight: 5 lbs

The tablet feeder remote removal system is for below-grade replacement of feed tubes and includes a set of one 12" extension, 12" handle and a cap with top threads to replace the standard cap.

Hydrant Flusher, Hydra-Max, 8 Tablets, 2.5" NST, 150-900 GPM, 4 ppm Cl, Aluminum, Swivel Elbow Discharge and Threaded, Dechlorination Tablet Feeder